My ZTE Blade V8 does not start or boot up
All the news on ZTE Blade V8 in our articles.
My ZTE Blade V8 does not start or boot up
Do not worry, there are many solutions if your ZTE Blade V8 does not start or boot up.
We will see in this article solutions like hard reset, battery reset, solving interference with applications or even solving electrical problems.
Your ZTE Blade V8 may eventually be under warranty or could be repaired by a specialist.
Unplug your ZTE Blade V8 from any electronic device
If your ZTE Blade V8 is connected to a computer, internet box or other, then we strongly recommend that you unplug it.
Indeed, it is possible that software incompatibilities could prevent your ZTE Blade V8 from starting or booting up.
Our other articles on ZTE Blade V8 can help you.
In this case, the solution is simply to unplug the USB cable from your phone.
Remove the battery from your ZTE Blade V8
Another possible solution is to remove the battery from your ZTE Blade V8. This can be a simple and effective solution if you want to start your ZTE Blade V8.
Factory restart under condition to start or boot up your ZTE Blade V8
Restarting with factory settings allows you to re-establish your phone as if it had come out of its shopping box, from a software point of view. If you have accumulated viruses, or unwanted software, this may be a good solution to start or boot up your ZTE Blade V8.
Refer to your manual to restore factory settings to your ZTE Blade V8, or call a professional. This will ensure that the steps have been made rightly on this perspective.
Be careful though, you will lose all your personal data by doing this.
Be sure to make a backup beforehand.
Battery does not work on your ZTE Blade V8
Battery fully discharged
If the battery is completely discharged, then there may not be enough power to start your ZTE Blade V8. We recommend that you load your ZTE Blade V8 and wait patiently.
Once the charging gauge is at least at 20%, then you will be able to restart your phone.
Note that it is not recommended charging your ZTE Blade V8 using a USB cable connected to a computer or other electronic device.
Indeed, the load would be slowed down, and software interference or even a virus could spread to your ZTE Blade V8.
Battery too old
Another problem on your ZTE Blade V8 may be that your battery is too old.
In this case, the only solution is to change it.
We advise you to go see a professional or test your battery on another ZTE Blade V8 before making a possible purchase of battery, sometimes expensive.
If all previous solutions do not work on your ZTE Blade V8
Use your warranty
Your ZTE Blade V8 may still be under warranty.
Most of the time, it is important for this step to have kept your receipt.
Best is to go and see your dealer who will help you to start your phone.
Go to an authorized repairer for your ZTE Blade V8
If you do not have a warranty, then it will be up to you to call a repairer.
We advise you to refer only to specialized repairers for your ZTE Blade V8. Be sure to ask for a quote before committing yourself with a professional who may charge you.
Why is my phone not turning on at all?
There are several possible reasons why your phone won’t turn on, from battery failure to software issues. But most times you can narrow it down to a few common problems, including: A drained battery. Your phone may be unresponsive because the battery is dead.
How do I get my ZTE phone to turn on?
How do I fix my ZTE boot loop?
Force restart the device by pressing power button for 10 seconds, your device should start normally. 2. If the device’s battery was zero & left uncharged for an extended period of time, the display will show a “Low battery” screen and shut down automatically.
How to Enter Recovery Mode on ZTE Blade V8 Lite – Open Secret Recovery Menu
8 ancillary questions
How do I fix Bootloop without factory reset?
You can try booting up in Safe Mode (power down, boot back up and as soon as you see your boot splash (quietly brilliant) hold vol-down until youre fully booted. You can try erasing your data and cache partitions in fastbootfastbootFastboot is a protocol and a tool of the same name. It is included with the Android SDK package used primarily to modify the flash filesystem via a USB connection from a host computer. It requires that the device be started in Fastboot mode.https://en.wikipedia.org › wiki › FastbootFastboot – Wikipedia, and then booting back up.
How do you get past a boot loop?
If any problem is detected, Startup Repair will attempt to fix Windows 10 reboot loop. If Startup Repair doesn’t fix the issue, you can go to “Command Prompt” under “Advanced options” and run the following command: Type “Bootrec /RebuildBcd” (without quotes) and then press Enter.
How do I fix a black screen on a ZTE phone?
Make sure, that your phone is off. Now press and hold these buttons: Volume Down + Volume Up + Power key.
How do I force a factory reset?
– Click on the ”Start” button in Windows.
– Press shift and click on ”Restart”.
– The system will guide you through the troubleshooting section.
– Click on ”Reset my PC”.
– Click on ”Keep my files”.
– The system will reboot itself, and factory settings are restored.
What do you do if your phone won’t turn on and it’s not dead?
Charge your phone for at least 30 minutes. Press and hold the power button for a few seconds. On your screen, tap Restart , or press and hold the power button for about 30 seconds, until your phone restarts.
How do I get out of boot loop?
Hold Shift then Start > Restart to boot Windows 10 into Advanced startup options. You might also open Settings (press Windows Key + I) then Update & Security > Recovery > Advanced startup > Restart now.
How do I force restart my ZTE phone?
With the device powered off, press and hold the Power + Volume up keys until the white ZTE screen appears.
What causes infinite boot loop?
The Windows boot loop problem is often the result of a device driver, a bad system component or hardware such as the hard disk that causes a Windows system to spontaneously reboot in the middle of the boot process. The result is a machine that can never boot completely and is stuck in a reboot loop.